Rubber tracks in the country, perhaps, one of the most successful solutions for the garden and garden. Durable, non-slip, environmentally friendly and relatively inexpensive, such paths will serve you faithfully for more than one year. We will tell about the features and types of such material on the features and types of such styling in this article.

Advantages and sphere of use of rubber tracks

Rubber tracks can be bulk, rolled, made in the form of overall plates or small blocks. Often such coatings can be found in dachas, household plots, in recreation areas or in playgrounds, in parking lots or indoors. As a rule, there are tracks from rubber crumbs or from waste, which remain after the processing of automotive tires. The initial raw material is first combined with polyurethane glue, and after it is planted into the stove, canvas or in a blocking.

Rubber tracks acquire all the positive properties of materials that are included in their composition:

• they are durable and very wear-resistant;
• thanks to good elasticity, any load is perfectly withstanding, not wondering, not abrupting, not deforming;
• transfer both low and high temperatures, as well as their sharp drops;
• such coatings do not slide, so widely used in places with increased security requirements;
• they are simple in laying and repair, do not need a difficult dismantling or replacement;
• rubber is environmentally friendly, does not harm health, you can safely walk with barefoot;
• such covers exist in a variety of colors, you can choose exactly the option that will most suit your design;
• rubber perfectly transfers the impact of ultraviolet;
• it is not damaged by rodents and harmful insects, does not mold, does not rot;
• the duration of the coating service exceeds 10 years;
• the price of rubber tracks for giving is relatively low and available to many consumers.

By cons of rubber, it is possible to be combustible. The material is afraid of fire, so it is impossible to mount it near open sources.

Thanks to its positive properties, rubber tracks have gained great popularity, and today the area of \u200b\u200btheir use is extremely wide. Such a coating can be found in playgrounds or in other gaming zones. Soft rubber noticeably reduces the risk of injury to kids during the fall. In addition, non-toxic material allows you to move on a barefoot, without bringing any harm to health.

Rubber tracks are very appropriate near pools and water attractions, because they have anti-slip properties. Rubber tile is often used for tracks in the country, as it is wear-resistant, inexpensive, does not require special care, serves for many years.

On sports grounds, game courts, cycling and offshore areas, stadiums and gym Rubber coating also found its application. As in the case of children's playgrounds, the material contributes to a decrease in the risk of injury athletes during classes.

Waterproof rubber is used in rooms with high humidity, for example, in bathrooms and toilets, in baths and saunas. Such a coating can be found in the production sector, for example, in the workshops, utility rooms.

Thanks to wear resistance and elasticity, the material perfectly transfers static and dynamic loads, which is why it is used on car parking, parking lots, warehouses, garages and hangars.

How to choose rubber tracks for summer cottages

Material for the creation of rubber tracks is worth choosing in view of how you plan to carry out installation. For example, for open pedestrian zones, a 50x50 cm tile with a thickness of about 1 cm is best suited. Mounted such material solely on a solid surface: concrete, asphalt coating.

If you want to be sealing the rubber zone near the water, for example, near the pool or water rides, then the dimensions of the tile may be the same, but the thickness you need a big one - it is 1.5 to 2 cm. Such a dense rubber tile will be different from The one is used for the paths in the country, but its operational characteristics will be significantly higher.

At the sports grounds, the tile must be threatened, its indicator will be at least 3 cm. This durable coating is able to withstand intense and constant loads, besides, it will also perform damping functions. It is also worth stacking such a tile only on a solid base, but its significant thickness will allow to hide small height differences.

So that the playing areas in the playgrounds were as safe as possible, choose the coating with a thickness of at least 4 cm. The tile of such thickness can be mounted not only on concrete or asphalt, but also on the ground or sand.

For sidewalks, rolled materials are best suitable, which are easily styled and connected using special plugs.

Installation of rubber tracks on the ground

Rubber coating for tracks in the country can be laid directly on the earth ground. To install rubber slabs on the soil, it is necessary to choose the material of the corresponding thickness. This indicator must exceed 4 cm, and the thicker there will be rubber, the better.

To lay the coating, you must first prepare a working foundation. To do this, the layer of the turf is removed from the ground, the weeds are chosen, the roots of the plants, after which the soil trambud and compact.

A cross-10 cm thick layer is poured into an endless ground. After that, a concrete solution is prepared from sand, water and cement, which is poured over a rubbed layer.

Deciding to buy rubber tiles for tracks in the country, do not forget to get both special elements for the border device with it. The border will make a track not only stronger, but also carefully. The coating elements are connected to each other with hollows, which are usually sold complete with tiles. The bushings contribute to the best and more dense connection of parts, do not allow the path to deform in the process of its operation.

Installation of rubber coating on a solid base

For laying on a solid surface, you can choose not such a thick tile, as in the case described above, you will be coated with a thickness of about 2 cm. A solid base provides for the presence of a concrete screed, wooden flooring or asphalt. Note that when using fine rubber, the working surface for laying must be as smooth as possible. If it is asphalt, it should not be cracks, pits and depressions, as well as noticeable bugs and protrusions. Before starting installation, the base should also be pretty progress. To do this, it is not even necessary to buy special primer, you can independently prepare the composition of acetone and polyurethane glue.

As for the concrete screed, it must be flat enough, at least some small defects on it are still allowed. The most important thing is to check the screed for detachments. If such places are present, it is desirable to clean it. Then concrete can be treated with all the same primer from polyurethane and acetone.

Please note: during the installation of the rubber track on a solid base, you need to make a small slope of the surface. It is necessary in order to flow from the coating water during precipitation.

When the working surface is properly prepared, the tile can be laid on it. Rubber elements are glued to the base using polyurethane glue. The glue, depending on its consistency, is applied to the surface with a roller or spatula. Then, putting the slab on the adhesive layer, it is pressed as follows and fixed in this position for a while until the composition is captured.

In this way, rubber fragments are mounted over the entire surface of the track. Once the glue freezes completely, it will be possible to walk along the path. To make the coating completed and tidy look, it is made up of borders.

How to make a path from old tires

If your finances do not allow you to buy ready-made rubber tracks to the country, you can save money and make paths from old tires, especially since such a material will not be difficult to get free or for the symbolic cost. Rubber from which tires manufactures, has all the previously described positive qualities. It is very wear-resistant, waterproof, dense, safe in operation, durable and reliable. Among other things, such a rubber coating for the paths for the country will be very symbolic, as you can find the spent material you can at the nearest one hundred.

We want to share with you a secret to create a cheap rubber track for a vegetable garden or a household plot. First, pay attention to what materials you need:

• auto strokes;
• shovel;
• axe;
• wooden bars;
• electric jigsaw;
• 7 cm long nails and hammer.

We describe the step by step process:

1. To begin with, the tire must be divided into parts by cutting off the tape of the tentor from the rim. Since tire rubber is very dense, it will be convenient to work not a simple knife, but an electrolovka. Rims need to be cut directly on the edge of the tread, so that the tape subsequently straightened.
2. Note that it is impossible to cut the rim across it, the jigsion should work solely around the circle of the tire. If you cut across, you can damage the tool with metal wires.
3. Now we will cut the protector so that the tape came out. Since the jigsaw cut the tire across it is impossible to cut the tire, and it is very difficult to do a knife, an ax or Bulgarian is useful to us. After overlooking the protector along with the inner wires, we will get peculiar rubber mats for the paths in the country.
4. The next stage we straighten our rubber ribbons and fix them in this position, having killed the edges to wooden bars. If you want a wide track of several rubber bands, feed them to the bars so that the gap remained in the midst. Through this clearance, water will subsequently leave during precipitation.
5. Prepare the details of the track, they can be mounted on the plot. To do this, in the selected location, we clean and compact the soil, we fall asleep its gravel layer, which is placed our coating.

Rubber tracks for giving. Video