Installing the door lock with your own hands Doors


 

Each of us, coming home, wants to feel protected, hidden from the surrounding world for a reliable door and a good castle. Installation of the lock on the entrance door - the process is very complex and responsible, in which there is no place for a hurry and where every detail is important. But if you clearly follow the technological process and be attentive, this procedure is quite forces by an ordinary person, not a specialist.

So why is the installation of locks on the door begins? To begin with, decide on the type of lock, and this is not as simple as it may seem at first glance. Today, the market presents a very wide range of both domestic and imported samples, which differ in price and in their characteristics. The choice of a specific option depends on many components, the most important of which are operating conditions and pricing policy. Although it is worth remembering that in this case it is not necessary to chase over unnecessary cheapness, since such economies are not justified. It is better to buy a more expensive one once, but a reliable castle than spending time and money from time to time to buy cheap samples, who have the only dignity - an affordable price.

 

Types of modern castles

To date, there are three main types of locks that can be used for entrance doors. The first option is the mounted locks used in the overwhelming majority of cases to close the doors and the gate in the utility rooms, sheds, garages. Locks like this type are not used to lock the entrance doors in residential premises, so they will not be considered in this article.

The following type of locks are overhead. Installation of an overhead lock is distinguished by its simplicity, while maintaining the strength of the structure. Outside, such locks are locked on the key, and from the inside to a special turntable, using the safety chain.

Nakladnoy_zamok.

 

 

The latter option is the most common - mortise locks. Installing a mortise lock is more complex, but they have a big aesthetics without disturbing the appearance of the door canvase. By their reliability, mortise locks are not inferior to their overhead analogues.

zamki4.

Each of the types of castles has its advantages and disadvantages. But no, even the most expensive and reliable castle can provide high-quality housing protection if its installation was not carried out according to the rules. To protect yourself and your home, installing the door lock with your own hands, you should strictly adhere to the rules and the correct sequence of work.

 

What is required for installation

To install the installation work, a certain tool will be required. The locking kit does not contain anything supernatural, all these tools are in every home. To work, you will need:

Electric drill;

The set of rolled different diameters;

Hammer (mall);

Roulette;

Chisel and chisel;

Pencil;

Corolnic

 

Installing a mortise castle

The installation of locks into the metal door is quite specific and is distinguished by a special complexity, in connection with which, in this article will not be considered. Today it will be about installing a mortise castle in wooden doors.

Your name mortise locks were obtained for ensuring that they completely interfere in the door leaf, providing reliable protection against intruders.

Before starting work, the door is fixed in such a way that there is a convenient approach from all sides, and the canvas itself was immovable. This will allow not only accurate markup, but also to carry out all work with maximum quality. Installing the lock in the interroom door in its technology is no different from installing the lock in the door input.

Badge groove under the castle body

The first stage of work is the inserting groove directly under the castle itself. To do this, it should be attached to the plastic of the canvas as it will be subsequently located inside the door and circling the contour, after which it starts to sample the socket. Initially, the maximum number of holes with the help of the electric drill is drilled. It is recommended to use the drum, the diameter of which is 1-2 mm more than the thickness of the lock. In the future, this will facilitate the installation of the castle in the groove. After drilling, the internal sides of the nest should be aligned using the chisels and chisels. It is important to ensure that the castle gets into place smoothly, without distortion.

1

 

When working, remember that it is not necessary to immediately drive the nest to the entire depth. It is better to go small passages, approximately 1 cm at a time.

zamok_2.

After sampling the socket, a test installation of the lock in the groove is performed, if it enters well, without difficulties, you can proceed to the next step - a sample to the front of the lock. For this, the lock is applied to the bar to the edge of the door and the contour will be burned. Then, the chisel, the desired depth is selected, so that the bar is flush with the surface of the door.

 

Sampling hole under the mechanism of the castle

The lock of the lock on the door continues, and the next stage is the device of the locking mechanism of the lock. For this, the lock is applied to the door of the door, adjusted to the thickness of the front strip, after which there are places for drilling. Arrow should be drilled by a thin drill, finalizing the chisel. Alternatively, you can use a thick drill, the desired diameter, driving a hole for setting the castle larva in one pass. Here you need to be very neat, the slightest cross will lead to the damage door.

Remember that if you install the lock with a handle and a snatch, you will need to drill additional holes for the rod that connects both sides of the handle, and the screws connecting the lining and the latch switch. It also should be very attentive, although, even if there are small defects, everything will be stopped after the overhead plank.

After performing all operations, it remains only to install the lock on its place and secure self-draws or screws. When using screws, it is recommended to pre-drill holes in the door with a thin drill, which will facilitate the spinning process.

door locks-1

Setting the castle

This is the final part of the work - the device of the grooves under the locking rigels of the lock and the latch (when it is present).

And here, first of all, high-quality markup is performed. There are several ways to apply it, but this article will consider the easiest way.

To do this, it is enough to lubricate the Bolt and the end of the latch with chalk, after which it is closed the door and turn the key in the lock - the smeared areas of the riglel and the latches will leave the track on the door frame, which will serve as the basis for sampling the nest.

The sample of the nest under the reiguel is made in the same way as the sample under the castle itself. The size of the nest should be with a margin on all sides for a couple of millimeters, which will provide a free course when operating the lock. After sampling, using self-screws or screws, the locking bar is attached and the lock is checked, using multiple opening / closing cycles. If the lock opens smoothly, without jerks and distortions, we can assume that the work is performed correctly.

pic11_1

Installing the mortise lock is horse.

 

Installation of false locks

Instructions for installing locks of this type is quite simple compared to mortise locks. Overhead locks are attached directly to the door leaf.

A set of tools is the same as in the previous case. First, markup is performed, with the designation of the sample location for the castle cylinder. For drilling, thin drills are used, which is done by the desired number of holes, followed by the revision of the chisel and chisel. Also, you can use special crowns to select a large diameter holes.

After the hole is ready, the lock is placed in place and fastened with screws or screws. To check the work, the lock opens several times / closes. The key has a slight and smooth.

The next step is to install a shut-off plank on the door frame. The door is covered, the lock is closed so that the shut-off riglele moves out. In the right place there is a markup and a shut-off bar, with fasteners on 4 self-press or screws.

Then the lock is checked, on the ease and smoothness of the stroke. If everything is in order, then work can be considered completed.

No name

As you can see, work on the installation of the castle, although quite complex, but with due patience and attentiveness, quite bye for everyone.

 

Be safe.

 

Installing the door lock with your own hands
28 votes 3.04 AVG. Rating ( 60% Score)

New comments

Add a comment