Laminate is a wear-resistant flooring. But over time or as a result of non-accurate use, the material may be deformed or different damage (chips, scratches, cracks). About how to repair the floor from laminate itself, and it will be discussed in our article.

How to repair scratches and chips on laminate

This problem may occur as a result of the movement of furniture or the fall of any heavy item to the floor. To eliminate scratches, you can use a pencil from wax (small damage) or a special smear (deep chips).

Before proceeding with such a process, how to repair the laminate, it is necessary to correctly choose the material for these purposes. The main requirement is the wax pencil or the mask must coincide with the flooring in a color shade.

When using a waxy pencil:

• scratches are cleaned of dust;
• they are painted with a pencil;
• using dry tissue removes extra wax;
• the renovated place is polished.

Now about how to repair the losses of laminate. For their high-quality filling, the smell is better to use the spatula. The putty is pre-applied to a piece of cropped laminate, which remained after laying outdoor coverage. After drying the surface, you should make sure that the mask on color coincides with the laminate. To remove excess material from the floor, a clean rag is used.

Such work, how to repair the chip in the laminate is carried out similarly to the injection of scratches. A distinctive feature of the technology is the use of a special putty, which will protect the floor from dust, dirt and a wet environment.

Putclone can be replaced with acrylic sealant. In this case, the chip seal procedure is repeated 2-3 times. This is due to the "shrinkage" sealant. And also: it is recommended to use a white sealant into which the caliper is added. Similarly, such a process is carried out how to repair a laminate dent.

How to repair the slots in the laminate

Causes of cracks:

• laying of poor-quality coverage (including substrate);
• completion of the installation of laminate from a different batch (mismatch of locks);
• the presence of an uneven base;
• constant temperature and humidity differences;
• neglecting the preparation of laminate, which lies in the acclimatization of material to the room for 2-3 days.

It should be noted that closesting the gaps should be done in a short time. Over time, they will become even more. And this is fraught with the discovery of the inner layer of floor covering. If the moisture falls into it, the laminate will have to be changed.

It appears the question: what to close the crack in the laminate? There are two ways:

• replace damaged laminate, pre-aligning the base;
• fill the slit with a composition containing a woody filler.

The first technology involves the replacement of the laminate, which occurs in the following sequence:

• plinth is removed;
• laminate is dismantled (towards the damaged area);
• combs and grooves of laminate with a damaged area are carefully examined;
• if necessary, the base is aligned and the substrate is replaced;
• replacing bad panels.

Special attention is paid to the proper connection of the laminate panels. The grooves and ridges of the floor covering are tested for the presence of dust and solid particles that are necessarily removed. In the process of laying a new laminate, it is necessary to avoid displacement and not use curves and cracked panels.

And how to repair laminate with your own hands using a special glue? Very simple - the composition is applied in the grooves of the floor covering. It should be done carefully so as not to glue the material to the base. The only nuance - glued panels are not subject to subsequent repairs. Subsequently, it is not possible to disassemble them without damage.

To eliminate cracks in the laminate, you can use the technologies for splitting the planks. This method is used in the case of laying floor covering without glue:

• all plinths are dismantled;
• wedges are installed in the deformation seam;
• wedges gently be bought;
• planks are connected to each other.

How to repair bloody on laminate

And whether it is possible to repair the laminate, which swept. That is, two adjacent panels begin to "push" each other, and the connection site becomes a V-shaped form.

There are several reasons for oily floating:

• non-compliance with the norms of laminate installation;
• lack of gap between the material and the wall;
• the mounting of the plinths is carried out directly to the laminate;
• the impact of moisture (a large amount of liquid is spilled on the floor, flooding neighbors).

To eliminate bloating:

• the board is removed, which is adjacent to the wall;
• panels are dried and cut in the longitudinal direction;
• heavy items are stacked on the swolmers;
• after 6-7 days, the condition of the laminate is checked.

If the above measures did not help, then you will have to resort to re-dismantling of the damaged laminate and replacing the new flooring. This directly applies to solving such a problem, how to repair a hole in the laminate.

How to repair stains on the laminate

Are the most common defect. Although removal of stains and does not apply to repair work. But in any case, the solution to this problem requires an application of considerable effort.

If possible, the removal of the stains must be carried out immediately. To do this, use the usual soft fabric. The removal of fat is made by a wet cloth moistened with dishwashes with the subsequent rubbing of the floor dry.

When hitting the floor, the paint, varnish or construction mixture will have to use acetone or solvent. Moreover, the removal of materials is made in the lowest time. After that, the laminate is wiping alternately with a damp and dry cloth.

Features of replacement of laminate panels without dismantling outdoor coating

Let's finish the article on how to repair the floor from laminate without removing the flooring. Stages of work:

• at the corners of the damaged panel (10-15 mm from the edge), holes are drilled;
• from the holes in the corners on both long sides, the lines are drawn;
• on the drawn line at the same distance there are still 3-4 holes;
• with the help of the manual disk saw, it was done along the line to a depth equal to the thickness of the laminate (it is forbidden to touch the substrate);
• drinking begins with the middle of the panel;
• with a sharp knife, a carved panel is withdrawn;
• the inner part of the old board (grooves and ridges) is removed from the next panels;
• with the help of a vacuum cleaner, the place is cleaned of dust and other garbage;
• the quality of neighboring panels is checked (if they are damaged, they are also dismantled);
• the new panel creates the bottom of the castle;
• a glue is applied around the perimeter of the laminate;
• the panel is placed in the cooked place;
• with clean fabric, excess glue is cleaned;
• heavy items are stacked on top of the new panel.

Video repair of laminate: