In the summer, almost everyone dreams to plunge into a strong heat, but here to equip a full-fledged landline pool on the plot of pocket not everyone. Fortunately, even not the highest protected citizens have the opportunity to buy an inflatable pool - affordable and easy to use. In such a reservoir and kids and adults, they will be happy to spend summer days, and if for some reason it is damaged, it can be repaired by his own. About how to make an inflatable pool, we will tell in this article.

Causes of damage to inflatable structures and methods for detecting defects

The inflatable pool is inexpensive and for the pocket of many. There is nothing difficult to inflate it and install in a suitable place on the plot, and if necessary, move somewhere else. Water in such a basin can also be replaced with ease, and with the arrival of cold, the design is dried, blown and hide until the next summer. All this is the indisputable advantages of such products, but the most significant disadvantages include fragility. Thin rubber is very easy to damage the sharp object, for example, putting on a sharp stone, a bitch or spike. Powing the pool shell can be pets or small children.

The causes of damage may be different, but this does not mean that the product will immediately have to throw away. Having found a hole in the inflatable pool, you can stick it and use the reservoir in the same mode. Determine the place of puncture in several ways:

1. That part of the pool that quickly flies the air, you need to inflate well. Then, slightly pressed the rubber, you should walk around the entire perimeter of the pool and listen, in where the air leaves. In the damage zone you will hear a characteristic sound and you can even feel the breeze of the breeze.
2. If the sound is not heard, moisten the palm and in the same way check the pool throughout the perimeter. Wet skin breathing wind from the cuts will be felt stronger.
3. If the product is small, and there is a roomy water tank nearby, inflate the pool and immerse them into the liquid. From the place where there is a puncture, air bubbles will be published.
4. The large pool can be checked for defects with a soap solution, which is suitable for the preparation of any detergent like a shampoo, gel, liquid soap, and the like. To begin with, do this solution, and then apply it to the entire surface of the product. In the place where there is a puncture, soap bubbles will appear. Finding a damaged zone, wipe it dry and circle a marker.

What can be stuck inflatable pool

Fashion first

The easiest, but short-lived method of fixing the product involves the use of simple stationery tape. So you can take a children's inflatable pool or some other, if, except forkchcha, there is nothing suitable at hand. Enough such repairs for a while, just a few days, but at this time you can search a more reliable method of fixing.

Before sticking the inflatable pool along the seam or on a flat surface, the material should be deguted with alcohol, and then challenged with small emery paper. On the rough surface of the scotch will last longer. When you processes a damaged zone, cut a piece of scotch and stick it into rubber.

Method of the second

It is possible to fix the product with glue, the pool must necessarily empty and pull the air. If you do not know what glue to take the inflatable pool, take an ordinary "moment". As in the case described above, at the beginning the place of the puncture should be detected, degreased and dry. For repair, except glue, you will also need a patch from the same material from which the pool itself is made, or a piece of fine rubber. The patch should also be cleaned and degreased.

Then the glue is applied on both prepared surfaces and are waiting for a few minutes until the adhesive enter the reaction with the material. Then the patch is applied to the place of the puncture and pressed with the effort. Cress the patch should be approximately 2-3 minutes, during which you can constantly squeeze air bubbles from under it. So that the lattice stuck securely, put the load on it and leave for 12 hours.

Method Third

Right and for a long time, take the inflatable pool for a long time, a special set for cold vulcanization of cameras will help. This is also a kind of latch with one sticky side. This patch is glued in the same way as in the case described above. Initially, an empty and blown pool is comfortably put on a flat surface. The location of damage is cleaned with shallow sandpaper and wipe the alcohol. Then from the margins remove the protective film and applied it with a sticky side to the pool wall. This place is loaded and leave the product for about 12 hours.

Four fashion

Intex inflatable basin manufacturers produce special kits to help stick the product if necessary. This set includes a PVC wrap, as well as a small tube with special glue. Unfortunately, the kit is not sold with the pool and take it separately. The repair process is similar to those described above. The puncture seat is cleaned, wipe the degreasing solution, dried. Then they apply glue to the latch and on the wall of the pool, the patch is applied to the appropriate place, pressed something heavy and left until drying.

If you have nothing suitable for the repair of an inflatable pool, if the repair of a simple scotch does not suit you, and you want a better result, consult professional. Fortunately, now there are specialized firms that provide similar services. True, you will have to pay money for it, but also the pool will be sworn to you firmly and for a long time.

Rules of operation of inflatable pools

So as not to look for a way to repair the inflatable pool, the easiest way to do it at all. For this, you just need to comply with security techniques, and it includes such rules:

1. By purchasing an inflatable product, open the packaging neatly and carefully, without using sharp items. Otherwise, you will spoil your pool before you begin to use it.
2. By installing the pool on the plot, place it on the distance from the bushes and trees, so that they do not damage the branches.
3. Do not inflate the pool too much, always leave a small stock of space. The probability of piercing inflated to the failure of the product is much higher than the pool, the walls of which are not so tugs and elastic. In addition, due to an excess of air, the reservoir may simply dispense the seams.
4. The pinned pool should also be left under the sun. The heated air inside the rubber walls will expand, and internally pressure is to rise.
5. So as not to put the pool on the sharp stone, glass or spike, be sure to lay the substrate under it.
6. Try to keep pets, especially cats and dogs, away from the reservoir, otherwise they can contact it or pierce claws.
7. So that the material served longer, clean the pool regularly and fill it with fresh water.
8. Jump into such a pool is also not worth it.

How to make an inflatable pool. Video