No wonder there is an expression "dog - a friend of man." Many families do not think their lives without a favorite pet. Other owners of their own country sites pursue more practical goals - the protection of the territory. In any case, if you brought a dog, you need to make it so that it is also comfortable and comfortable to live with you. To do this, build a special housing - Konure, to make it simple enough. How to do this work correctly, find out this article.

Why do you need a loaf for a dog?

Installing a dog for a dog near a private house necessary, at a minimum, 3 reasons:

• the PSA will have a reliable shelter from bad weather;
• it will be his personal place to rest;
• an animal will know that this is his place, which is very important in raising a pet.

Concei Design Requirements

Despite the fact that this is "just" a booth for an animal, make it right and kindly. For this:

1. Take high-quality materials so that it does not occur from the season to repair it.
2. Make an attractive design, as it will be a full-fledged part of landscape design near the house, and more pleasant to look at the beautiful booth.
3. Properly determine the size of the coneers so that the dog is comfortable to live in it.
4. Make a removable roof - it will facilitate prophylactic treatment inside from parasites and will help to provide first assistance to the animal if it squeaks or circumscribed.
5. Install the cone on a small elevation to prevent the rainwater accumulation inside
   

   Important! Choosing a booth design, preview the photo of a dog for a dog of ready-made projects or use the ideas of the design of ready-made designs exhibited for sale in special stores.

How to choose the size of the conera?

For each dog, a certain size of the coneers is suitable. It is necessary to know how to adhere to certain standards when drafting a diagram of a drawing of a dog for a dog.

When developing a plan, consider the following standard requirements:

• 70 * 55 * 60 cm - sizes of booths for dogs of small size, for example, fees or Shi-Tzu;
• 120 * 75 * 80 cm - for the rocks of the Middle Size of the Type of Charpecia or Rottweiler;
• 140 * 100 * 95 cm. Large dogs, such as Caucasian Shepherd or Dog.
  

  Important! Take into account the sequence of the above parameters - they correspond to the length-width-height of the booth.

Another way to determine the parameters of the dog's coneers are the specific dimensions of the body parts of the PSA:

1. The width of the booth should correspond to the length of the body of the dog from the nose before the start of the tail.
2. The depth of the cone and its height is the height of the dog.
3. The height of the Laza is equal to the height of the PSA in the withers.
4. The width of the lazium corresponds to the breast width plus 5-10 cm.
   

   Important! Before proceeding to work, choose a more convenient method of miscaluing parameters and do all measurements correctly.

Materials for booth

To quickly and easily build a coneer for a dog, prepare in advance all the necessary materials. Below is a list of all necessary parts for a specific option of the booth, the assembly instruction is set out below:

• wooden boards with a cross section of 100 * 100, 100 * 50, 40 * 40 mm;
• batten;
• plywood sheet;
• lining for outdoor decoration;
• fillet;
• decorative rails;
• ruberoid;
• soft tile;
• galvanized nails;
• mineral wool or foam;
• antiseptic solution for wood;
• pergamine;
• several concrete slabs;
• staples with a stapler.

How to make a cone for a dog with your own hands?

Collect the PSA booth, consistently perform the following actions:

1. Choose a suitable place for the coneers.
2. Drop a small pit with an area corresponding to the size of the booth.
3. Squeeze the concrete poles or stoves in such a way that part of them look out above the ground.
4. Treat all sawn timber antiseptic.
5. Wait for drying.
6. Drink 2 boards 40 * 40 mm long with a width of the coneers.
7. They will fasten the sex board on them - it will be the finished floor for the coneers.
8. Drink 4 bars 100 * 100 along the length of equal height of the booth with a gap of 40-50 mm.
9. Install them as a support on the bottom.
10. Outside on the racks, secure the lining around the perimeter.
    

    Important! To secure all parts, take galvanized nails of suitable length.

11. From the 40 * 40 bars and plywood collect the roof of the booth.
    

    Important! If the contents of the large size, and the roof is double, be sure to submit several backups inside so that the plywood has not saved.

12. Unlock the surface of plywood.
13. Place the foam or mineral wool around the perimeter.
14. Secure the second sheet of plywood from above.
15. Place the rubberoid on the phaneur, and then several sheets of soft tiles - it will add the attractiveness of the design.
    

    Important! So that in the future it is convenient to remove the roof, make a special handle on it.

16. Will the bottom of the Konura pergamin.
17. Secure the material using a building stapler with brackets.
18. Make laying insulation.
19. Cover it from top of a pergamine.
20. Click on top of the finished floor prepared in advance and apply an extra sheet of plywood from above.
    

    Important! The last action will not allow constant jams and damage to the animal claws in the cracks.

21. Similar procedure, follow with all the walls of the booth.
22. On the entire perimeter at the bottom of the coneers and in the corners, heger.
23. Take the threshold and LAZ.
24. Fix the roof on the pins in the corners - they can be made from ordinary nails, scuffing the caps or take special building stiletto.
    

    Important! In the front of the roofs, the holes in the pins at the appropriate distance drill.

25. Color design outside in your chosen color or leave the natural color of wood if you took a good lining.
    

    Important! Inside a dog for a dog, it is impossible to paint - it can harm her health, because the pet will constantly come into contact with the wool and skin with toxic paint.

Video

Browse the video example of how to make a booth with insulation for PSA to quickly understand what your design can be.

Conclusion

As you were convinced, build a dog for a dog with your own hands at all is not difficult. Here you can even easily give the will of your fantasy and make a real masterpiece and an example of artistic art. The main thing is to implement such an idea time. Be careful to your pet, and he will answer you loyalty and caress.