At this time, many types of roofing coatings were invented. Among them are the most popular material for the roof roof - Ondulin. He gained popularity thanks to such qualities as wear resistance, efficiency and external beauty.

Preparing for the roof of the roof of Ondulin

Ontulin is a roof coating material that is light, wear-resistant, wave-like sheets capable of protecting the roof of the house from the effect of precipitation, temperature drops and other negative impacts of the atmospheric environment. Roof from Ondulina - This is a strong, solid design, suitable for buildings of any destination in any climatic conditions.

If roofing works for some reason, it is necessary to produce in the shortest possible time, then when choosing a material, the right solution is Ontulin. Its installation is not complicated and does not require high time and strength. When carrying out work, you can significantly save. Laying ondulin is admissible to the old roof. Complex toolkit and special knowledge for this are not needed. The owner of the dwelling can easily cope with such a task as the roof of the roof of Ondulin with her own hands.

Before laying on an old coating, it is necessary to check the fortress of the rafter system and decide whether it is capable of making an even greater load than it was before.

Ogelin Roof

Making sure that the work on the roof device can be continued, it is necessary to kill an additional fraud from the tree to it, which will be subsequently attached ondulin. This action will give the roof additional heat and waterproofing properties.

The neckenet must be quite frequent, because the material itself is soft enough and in the case of the application of a large-scale crate, it is possible to sagging under the weight of the snow dropped. Mount it is necessary to mount the crate, given the angle of the roof of the roof and the focus of the wind, starting with the least refiring side. The bars of the crates are attached by their axes at the same distance. The rod of the roof should have an angle of 20 degrees. Ondulin is attached to the beams of the crates, beams - to the roof rafters. The gap between them can fluctuate from 60 to 80 cm. If it exceeds 80 cm. The auxiliary rails are nourished between the bars.

Rules of mounting ondulin on the roof

So that the Ondulin Roof turned out to be high-quality and served for many years, it is necessary to own various subtleties regarding the installation of this material:

• if in the process of work there is a need to go through the material already laid sheets, it is better for the crest of the wave, because The space between the waves can crack under the severity of man;
• it is possible to obtain roofing work using ondulin at air temperature from -5 to +30 C. If the temperature goes beyond the range of this range, the installation should be postponed for a more favorable day;
• to secure one onduline sheet, you need to spend no less than 20 nails attached by a set to the material. This quantity is necessary to make reliability coverage, strong wind resistance;
• the wooden fence is made from bars with a cross section of 60x40 mm. The frequency affects the durability of the finished coating and depends on the corner of the roof of the roof:
  • if the angle is less than 10 degrees, a solid, plywood lamp is applied;
  • if the magnitude of the angle ranges from 10 to 15 degrees, the cells should not be more than 450 mm;
  • if the angle exceeds 15 degrees, then the limit distance between the bars is 610 mm.
• fixing Ondulin, you need to carefully measure the linearity of the joints horizontally and vertically. In no case cannot be allowed to stretch the sheet on the roof plane. Before conspicing Ondulin, it should once again check the uniformity of its location throughout the work surface;
• it is best to cut it with a woodwood with a woodwood, having pre-groaning it with oil to avoid jams.

The laying of the first row of Ondulin is proceeded from the bottom edge. The following row is mounted from a sheet cut along into two parts. The sheet is nailed horizontally, special nails, similar to screws and firmly fixing in the wood. Mounting the first row must be installed fasteners in each crest of the wave, and in the following rows - through one. The second row stacked the brass with the first.

Vertically, Ondulin is fixed on bars. The backstage going along should be equal to at least one wave, walking across - fifteen centimeters.

The last work step is the installation of skate elements. They are fixed in the wave of sheets. To form an inner angle at the junction of the roof slot, you will need auxiliary doom.

The cost of the roof of the roof is Ondulin

Before starting work, it is necessary to calculate how much the roof of the roof of the Ondulin can do. The price of it fluctuates about 400 rubles and depends on the company producing this material, from the additional services offered by it, such as delivery, an increase in price, or an action that reduces the cost.

The price that professional roofers can be requested for their services may depend on various factors:

• roof shape;
• the need to prepare and additional services;
• the right amount of special nails and their presence;
• experience and professional level of masters.

Highly qualified specialists guarantee quality and timely execution of work, but at the same time it is much more expensive. Last year, the average cost ranged from 200 to 300 rubles per square meter.

Of course, this is a tangible consumption, therefore, if there is an opportunity, it is better to conduct work on the roof of the roof of Ondulin. Photo , posted on this page, allow you to better understand how this can be done.

With independent coating, the roof will have to pay only for the material. To calculate how much it will cost you to measure the area of \u200b\u200bthe roof and multiply it on the value of the material.

Pluses and cons of Ondulina

Like any Ondulin material has its weak and strengths. Its advantages can be attributed to:

• low price;
• ease;
• long service life;
• uncomplicated installation that does not require special education;
• environmental friendliness;
• efficiency due to the possibility of its styling on the old coating;
• correction of the size of the sheet and its form by means of conventional cutting;
• high resistance to fungus, acids and alkalis.

The essential minuses of Ondulin can be considered:

• combustion;
• roughness that does not give the snow to slip from the roof;
• a small choice of colors;
• burnout in the sun;
• fragility of material and, as a result, the need to install a wooden crate;
• reliability in the frost and softening in the sun.

After examining the above-mentioned advantages and disadvantages, it is possible to estimate the feasibility of the roof of the roof of Ondulin. Video with step-by-step guide, see below.