The wonders of the landscape design on its garden or the country area can create each, while possessing minimal resources. The only important condition is the fantasy of the artist. Bright flower compositions are an integral element of garden design. But not less than flowers, important and flower beds in which they will be. Multiple style and design of flower beds are easy to do from a completely ordinary and at first glance that do not represent any interest, things, for example, automotive tires.

Necessary materials and tools

Tires (Tires) - Source material for the manufacture of flower. If the flower beds and carbbles from the tires will be simple form, recommend using domestic, and for complex elements in the manufacture of elements it is best to take imported products, they have rubber softer and better carries away. Choosing between summer and winter tires, the choice should be stopped on the winter. And yet, the tread protector must be most worn out, then it will be easier to turn it. Also, you will need:

• A well-fulfilled knife is the main tool of the wizard. The knife for cutting should be sharp, then all the cuts will look carefully (some use hacksaw or jigsaw).
• Chalk, marker, soap - any of them is suitable in order to apply a lines of the incision on the tire.
• Gloves to protect your hands, as the work is dirty, and the tracks from the rubber are designed hard.
• Paint for final finishes. Any paint suitable for exterior work is suitable, but products with a shiny surface (enamel) will look more spectacular.

• There may be needed any other elements for the decor - the beaks, pebbles - at the discretion of the authors and their fantasy.
• We take the trained tire, to start it you need to clean from dirt, well wash, without soap, and dried. Next, carefully clean from sand, carefully inspect, remove the wire, nails or other foreign elements. Further, two options are possible - the tires with the disk and tires without disks. To create a vase with a bottom, you need to use a tire with a disk, the disk will serve the bottom and subsequently you will not need drainage. We will use a simple tire to decorate the flower garden, as well as for individual group compositions - many options.
• We draw on the outer side of the bus line, first simply a flat circle, and we will cut about 1/3 part of the tire, we will produce a flower leaf from a deeper part. Several options. It can be a flower (petals are large or small), an animal or a bird. What we need to do is now - draw petals if they are in our design and which edges will be in future animals or birds. It is recommended to make petals up to 12 cm, no more, otherwise there will be problems with the form of an end product.

• Start cutting out. The tire from the disk is not removed, cut exactly on the intended line, using the tool to do with which you easier to work. If you use a knife in your work, it is recommended to make water with soap. A figurine cutting is much easier to perform a jigsaw.
• The most difficult part of the work is to turn the tire inside out. Here, really without physical strength, do not do, and the skill will come in handy. I turn down the deep bottom of the cut down, then we step on the edge of the foot (or pressing the hand) and pull the edges. The resulting part at the same time it is necessary to hold the knee. Then we give around the circumference with your hands, flexing the edges. The cut upper part is still useful to us - this is a ready-made decor for flower beds, we will only make some small cuts on the inner ring that will burst into the ground.
• Now the most fascinating part begins. The form is ready, we will give it a final look. For coloring, the surface must be prepared, washed with a brush, better with a degreasing agent. From how paint will fall on the surface, the presentable appearance of flower beds depends. Then dried rubber and proceed to the artistic part.

Operation of work - instruction

• We take the trained tire, to start it you need to clean from dirt, well wash, without soap, and dried. Next, carefully clean from sand, carefully inspect, remove the wire, nails or other foreign elements. Further, two options are possible - the tires with the disk and tires without disks. To create a vase with a bottom, you need to use a tire with a disk, the disk will serve the bottom and subsequently you will not need drainage. We will use a simple tire to decorate the flower garden, as well as for individual group compositions - many options.
• We draw on the outer side of the bus line, first simply a flat circle, and we will cut about 1/3 part of the tire, we will produce a flower leaf from a deeper part. Several options. It can be a flower (petals are large or small), an animal or a bird. What we need to do is now - draw petals if they are in our design and which edges will be in future animals or birds. It is recommended to make petals up to 12 cm, no more, otherwise there will be problems with the form of an end product.

• Start cutting out. The tire from the disk is not removed, cut exactly on the intended line, using the tool to do with which you easier to work. If you use a knife in your work, it is recommended to make water with soap. A figurine cutting is much easier to perform a jigsaw.
• The most difficult part of the work is to turn the tire inside out. Here, really without physical strength, do not do, and the skill will come in handy. I turn down the deep bottom of the cut down, then we step on the edge of the foot (or pressing the hand) and pull the edges. The resulting part at the same time it is necessary to hold the knee. Then we give around the circumference with your hands, flexing the edges. The cut upper part is still useful to us - this is a ready-made decor for flower beds, we will only make some small cuts on the inner ring that will burst into the ground.
• Now the most fascinating part begins. The form is ready, we will give it a final look. For coloring, the surface must be prepared, washed with a brush, better with a degreasing agent. From the paint will fall on the surface, the presentable appearance of flower beds depends. Then dried with rubber and bouts to the artistic part.

The most simple variants of the flower beds

Make a flower beds from the tires with their own hands simple enough. But it is better to start with simpler options. The easiest solution, for those who do not want or do not know how to cut out - use in the design of flowerbed only paint. But even this technique allows you to create an original product. Options for execution Multiple:

• Put each other tires of one diameter, while painting in different ways - decorative member horizontally or vertically. Or paint under the snake, is also very interesting.
• Wonderful flowerbeds from automotive tires will turn out if you fold vertically tires of different diameters, each tier is painted with different colors and plant colors.
• From the solid tire it is easy to perform the suspension. To do this, it is necessary to overlap the bottom of the tires (the easiest way to cut the plug plug), and upstairs strengthened the chain or thick rope. Since the weight of the tires together with the ground is quite large, the attachments should be as reliable as possible (minimum 4, better 6-8). Long bolts are used as elements for connecting a circuit with a tire. They are inserted from the inside of the tire through the washer, and on top bend in the hook. Using the washer allows you to distribute the load.
• From whole tires often make long flower beds, while they are combined vertically and horizontally.
• Flower flower. The flower itself is designed in the form of a flower - such a seven flower, in the center of a solid tire-center of the flower, the tires are located in a circle, dried by half vertical, forming petals.

In all simple variants, the flower effect of entertainment is achieved by color in combination with various decorative elements. It can be:

• beading drawings
• drawings with paints,
• patterns
• ornaments.

The use of beads is a very painstaking job, but on its conclusion, the flower bed becomes really original and very attractive. Any glue is suitable for fastening the beads, interacting with paint and varnish coating. It is much easier, but no less effectively looks at paint drawings. In order for them to look as much as possible, the background color is recommended to select light (cream, white, yellow or pink). Patterns and ornaments look perfectly on any background. It is best to make them either black or dark shades of red, green or blue.

Flower beds - Figures

• Multi-tier flower bed, but already from the cutting tires, resembles a traditional cascade fountain. Only in our case - floral. In this case, the tires are cut in the middle without petals, a smooth line. It is desirable to take tires from very large to medium and shallow so that the difference in the size is visually noticeable. Next, choose the biggest tire, that is, its lower half and make the bottom of the flower beds from it. I fall asleep sand and crushed in the bottom, we will be tamed a little, then we embarrass the fertile layer of the Earth. In the center of the resulting flower beds, we establish a ring of smaller diameter and again lay asleep drainage and soil. You need to make a minimum of 4 tiers. Between the rings, low-colored flowers are planted, and on the upper tiers, various types of curly vegetation look more impressively. Color for coloring of the tires in such a flowerbe it is better to take a monophonic or with wide stripes, because the flowers planted on the tiers are medium or small and color on the tires can not be fragmented.

• Flower bed with petals - the most common variant of a vase performed from the tread turned out (manufactured as described in the instructions). It would seem that the base is one thing, but how much of it is completely unlike each other of products. Flowers are characterized by dimensions and shape of petals (triangular, rounded, straight), they can be painted in one color or with different petals, they also differ in diameter and height. Some vases are puzzled and stand right on Earth, others - on the leg. In some vases, wide in diameter and intended for disembarking low plants, the petals are convex and curved. Lesse diameter vases and intended for high plants, have sharp gear edges located vertically. Very spectacularly, these vases will look in group compositions in which horizontal and vertical elements are combined.

• Flower bed with petals, but on the leg. Such a flowerbed is performed from a tire with a disc in the middle. It differs from the previous version of the flower beds by the fact that the disk is not removed and the result is an excellent decorative vase. Such vases are perfectly grouped together, especially if they differ in height and sizes.
• Cheerful animals - a turtle. Vasons in the form of animals and birds look very attractive. They are installed both by single compositions and groups. The turtle is performed by the team - from a solid tire and a cutting tread. Very simple manufacturer. Lape protectors are strengthened with wires - brackets, add the neck (plastic tube) and head, you can with a hat. Coloring it, of course, you need a turtle, do not forget to draw your eyes.
• Very elegant version of flower beds - White Swan. Such a flower bed is performed from the tread turned. It requires already a certain skill for its execution, since it will be necessary to form separate elements from the tire, the tail, neck, head. Therefore, when applying the outline of the future swan you need to use different colors to not confuse. After the contour is cut, we act further according to the instructions - turn it out. The assembly is made as follows: from the girlfriend (plastic you can) make the beak, then stain it, connect the halves of the head, do not forget to insert the beak, fix the design by self-draws. Where the swan has eyes, we also screw the screws, then we close them with circles. Next, you need to work on a plastic figure so that it looks like a swan - lift your head and fix it too. But, by the way, the swan can be not only white, for playgrounds are recommended to come up with fabulous birds - on the other side, maybe multicolored.

• An interesting option when the flower bed itself is made in the form of a flower, but not a simple bowl with petals, but as a rose or poppy. Such flower beds are already design elements and are single. And the flowers in them are planted more for the accent, in small quantities. For the manufacture of such a flower, the entire tire without waste is used. Large diameter tires are not suitable here, as it is single compositions. The bed of flower beds is manufactured according to the instructions, only the cut-off top of the top are made additional petals, they must be pre-cut into strips.

Also, the design flower beds made of tires are performed as:

• mushrooms,
• different little men
• dwarfs.

The same group includes both a wonderful spruit - flower bed in two tiers representing the rings of the spruit. This composition decorates - the head of the spruit makes big eyes. A few other original decoration options, as well as the manufacture of flower beds from tires, photos and video materials from the article will demonstrate in the best possible way.