Slidors - is the latest fashion pack in the glazing of balconies and loggias. This system is similar to sliding cabinets and works on the same principle. Practicality, saving space and original appearance - only the beginning of a long list of advantages of this technology.

What is SLIDORS system and what is its feature

The Slidors brand appeared on the market at the beginning of the two thousands. The project immediately aroused interest, as it was a joint Russian-Korean project. Subsequently, it turned out that attention was quite justified, since the quality of products was not inferior to European manufacturers of ordinary swing windows.

The main facilities are focused on the Izumrud-Extrusion plant, which produces plastic reinforced metal profiles. Products are specially adapted by the Russian consumer.

Quality control is carried out by experts from South Korea. All materials are supplied from Japan.

Currently, the SLIDORS system continues to develop, the product range expands, new modifications of PFC profiles are manufactured. The system is adapted for use not only in the territory of the Russian Federation, but also from the CIS and Baltic countries. More than 19 countries of the world have already made a choice in favor of the SLIDORS system.

Advantages of glazing balconies Sladudors:

1. Installation on the three-chamber profile windows made it possible to significantly reduce heat loss. Accordingly, the windows are immediately considered energy saving. The system is more than wood, cheaper plastic and ergonomic aluminum.
2. The ability to install a package with a sound insulation effect, that is, the room will not reach outsiders from the street.
3. A special seal with windproof and moisture insert, used in the system, provides good sealing, waterproofing, wind protection, drafts and dust from the street. The roller channel prevents wetting, as well as the penetration of water inside.
4. In the production of PVC, a special mixture is used, in which plastic withstands the strongest frosts. The profile composition refers to the frost-resistant.
5. The use of stainless fittings in the window frame frame, as well as a roller system with a double safety margin, withstands weight 2-3 times more than the window unit weighs, which made it possible to achieve maximum reliability of the design.
6. The system is at one level at a price with sliding aluminum windows, according to the characteristics, they exceed them. Therefore, the price criterion - quality speaks towards the Slidors system.
7. Thanks to the sickle lock inside the system, as well as steel galvanized reinforcement, the stiffness of the structure increases, that is, ensures the safety of the dwelling.
8. Thanks to a comfortable design, it allows you to save a lot of useful space on the loggia or balcony.
9. The material does not contain toxins - this is confirmed by a fire safety certificate and sanitary-epidemiological conclusion.
10. Insect protection. Mosquito net is easy to install anywhere in the window.
11. Great applications. The SLIDORS system is used not only for glazing balconies and loggias, but also for the manufacture of interior partitions, wardrobes, sliding doors.
12. The small weight of the design is very suitable for houses with non-stable parapet, for example, breeze, Khrushchev.
13. The SLIDORS system gives any color and texture, the procedure is carried out after installation.
14. The service life is 50 years.

Specifications SLIDORS system

• opening: sliding system, analogue of a coupe,
• seals: double brush seal, filingps, with unique moisture protection and windproof inserts, which prevent the blowing and removal of sash,
• technical frame profile: width 58, 60 or 70 mm,
• gloomy: glass 3-6 mm or double-glazed windows 14-8mm having high heat transfer resistance,
• heat insulation: Ropp \u003d 0.15 m2 * C / W with glass, Ropp \u003d 0.33 m2 * C / W - with a glass,
• soundproofing: 47 dB,
• frame: galvanized reinforcement, which is provided by durable angular compounds and steel elements,
• protection against hacking: Provided by a sickle lock that does not face.

Slidors Installation Instructions

Installation Slidors is not particularly different from the installation of other plastic systems, but there are some features. The elements of the plastic profile of the SLIDORS system are connected to the finished design due to the patented angular connections. Therefore, glazing slidesdors of balconies and loggias completely does not have welded seams.

For work you will need:

• screwdriver
• screwdriver,
• fasteners,
• self-tapping screw
• dowel with screws.

Stages of work:

1. Ordering systems:

• remove the sizes of the window if the slidors is mounted in the finished opening, then it is necessary to accurately measure the height and width of the opening, if the glazing of the open balcony is planned, you will need a drawing,
• contact a distributor
• order Production and delivery of the system,
• check the package, for this unpack all the boxes and compare their content with the invoice, in addition, you need to carefully examine the windows on the subject of scratches and cracks, with independent installation, warranty service is not provided.

2. Preparation:

• clear profile from the protective film,
• collect elements of the profile in the frame, use screws and corners for consolidation,
• unpack the fasteners of the glass package,
• unpack and prepare rubber gaskets,
• prepare roller mechanisms
• clean the glass from the protective film.

Advice: It is advisable to prepare on a flat surface place. Stop it with old sheets and all design elements spread on it, so that nothing has lost.

3. Installation:

• insert the collected frame in the opening,
• fasten with fixing plates and dowels,
• insert crimp rubber in the opening for glass,
• paste glass
• install fixing rubber gaskets,
• secure the glass with the help of fixing plastic clamps, the clamps are inserted into the top, then below, and only then on the sides, you need to insert them around the edges, and the middle is gently tighten to complete fixation,
• on the same principle to collect sash,
• first, we set the outer sash, if the rollers are not screwed to it, they mount them on their own, the corresponding markup will be on the frame,
• if the rail guide is not screwed to the frame, set it yourself,
• insert the top of the sash in the top groove rails,
• insert the lower part of the sash to the lower groove rails,
• similarly, mount the inner sash.

Finishing work:

• check the smoothness of the stroke,
• mount using self-suicide castle screws,
• krepim, a response plate,
• install between the sash brush seals,
• from the streets drill in the hole of the hole through which condensate will be departed,
• if you plan to install mosquito nets, fastened on the frame fixing elements,
• we blow all the holes between the frame and the wall of the mounting foam,
• the next day, foam is cut off,
• installation is completed.

The first 2-3 weeks window closes enough tight, this is due to the fact that the seal, the lock and rollers are not yet rolling. If the problem has not gone in a month, you need to sort out the design or lubricate the roller mechanism with oil.

Premosts about the installation of balconies and loggias in winter

1. In winter, the replacement of windows leads to the supercooling of the room, with all the ensuing consequences, like the freezing of heating pipes and the colds of the owners of the apartment or at home. In practice, it is not. The dismantling of old windows is made within 10-20 minutes. All elements of the new design are collected in advance, so the installation process does not take more than 10 minutes. Total, the room is under the influence of cold air no more than half an hour.
2. Glazing Sladors, reviews about which they say that the profile established in winter was twisted, most likely have the goal of black PR. Inexperienced masters explain this by getting from a cold warehouse to the room, plastic under the influence of the temperature difference unscrews, by analogy with a tree. From a scientific point of view, the thermal conductivity of plastic is significantly less than that of the tree, therefore it is not deformed. Naturally, this does not apply to high temperatures, let's say, if you wear a cigarette profile or inactively remove the protective film with a gas burner.
3. Installation is carried out poorly. This statement came up with the sellers of the windows themselves so that buyers do not take the goods on discounts. When installing the window in winter, any shortcomings, especially associated with drafts, are immediately visible and immediately eliminated.
4. The strangest of all, the view that the mounting foam loses its properties. There are quite a lot of foam varieties, some are designed specifically for work in the winter. In addition, the main active substance of the mounting foam has thermal conductivity close to zero, therefore it is not exposed to low temperatures.

Operation of glazing loggia slidesdors and balconies by 90 percent depends on the use of high-quality materials.

Conclusions when installing the glazing of balconies and loggia systems Slideshome in winter:

• special New Year discounts,
• reducing product production
• much attention to installing in the winter.

Slidors System Care Tips

• when removing from glass of any contaminants, do not use sharp and cutting tools,
• it is not recommended to use acetone or other aggressive tools, as they can damage plastic and make it rough,
• accessories do not clean with pasta or powders. It is recommended to use warm water using liquid soap or shampoo,
• details (all moving parts) in windows once every six months Lubricate with machinery,
• remains from building solutions is better cleaning with a wooden spatula or blade,
• clear several times a year rubber seal from accumulated dust and dirt, and at the end to lubricate a special tool that will additionally protect from dust and dirt,
• time time to clean from dirt drainage,
• regular ventilating room.

Councils for the care of windowsides during the glazing of balconies Slidesh's system:

• do not use abrasive pastes, as you can worsen the quality of the coating,
• it is better to use a warm soap solution,
• seals should be cleaned with water, and lubricate with silicone oil or glycerin several times a year.