Car lubers have to spend a lot of time in the garage, and there, with the onset of cold weather, it becomes very comfortable because it is not much warmer in it than on the street. There are thoughts that it would not be bad to drop this room.

Heat the garage is not difficult: built the furnace for heating the garage from the brick or put the burzhuyk, and the tops of the wood. But when is it to pay time for work, if you need to throw up firewood all the time in this voracious fireboard? It turns out that it is not a stove for you, and you for the stove. Do you want a garage oven with your own hands that burns for a long time without your intervention? If so, then to the case.

Oven on "Working"

This is a furnace, which can be collected with your own hands. It is simple, efficient, economical and reliable. Fuel for her: used oil is cheap. The design resembles the "bourgeitogo".

  Advantages

The advantages of such a furnace a lot:

• easy to manufacture;
• eco-friendly: emissions of smoke and soot are absent;
• uses as a fuel to work out that needs to be disposed of;
• mobile - can easily be collected and disassemble;
• no nozzle and dropper;
• fireproof - the fire does not develop into an open flame, since only pairs of working out are burning;
• a heating system can be attached to the oven for the garage for the garage and even adjust the temperature. The design is very simple: it is enough to install the tank on the furnace. In the upper part of its part, in the bottom - the return. If necessary, it can even be prepared for themselves to have a snack.

Design

It is not difficult to make such an oven for the garage with your own hands. Its components:

• two tanks;
• pipe with lots of holes connecting these containers;
• nozzle on the upper capacity, and on it a pipe for an exhaust;
• The upper part is removable for the possibility of cleaning the burner;

Works as follows:

• the furnace is in the lower part, which holds 12 liters. Part-time it serves as a tank for fuel;
• working poured through the hole at the top;
• it is necessary to pick up a lid, which despite its simplicity, performs an important function - on what position it is located, it depends on how much the fuel is burning, that is, the room temperature. This is a kind, a console that is regulated by the supply of oxygen;
• the container, which is above and the pipes perform the role of heating elements. If the furnace is warm up to the maximum, then they will have a temperature of 800 to 900 degrees.

What are the main furnace elements made from?

For the manufacture of the furnace will need the following material:

• for the upper tank and pipes - iron thickness from 4 to 6 mm;
• exhaust pipe - galvanized iron.

Specifications

• dimensions: Height (excluding pipe) - 0.7 m;
• the diameter of the upper tank is 0.5 m;
• the diameter of the bottom capacity is 0.35 m;
• mass: approximately 30 kg;
• the diameter of the exhaust pipe is 10.5 cm;
• exhaust oil consumption - 0.5-1.5 l per hour.

Useful advice

• the oven for the garage will be able to work even on untreated workout;
• the optimal height of the chimney is 4 m;
• for good traction, exclude horizontal sections;
• clean the stove and chimney clean each ten;
• say will be less if the diameter of the top pipe is large than the exhaust;
• The degree of clogging of the chimney is inversely proportional to its diameter: the greater, the less clogs;
• when burning, the lower tank is placed on paper, pouring on it to work (0.5 l) and ignited;
• in 10 minutes. poured about 5 liters of testing, and after a while, as much as;
• substances that can flash or explode, remove from the furnace away.

Homemade garage furnace on firewood

There are design furnaces for garage on firewood, burning in which lasts from 7 to 60 hours.

What is needed for manufacture?

If you stop at this version of the wood dryer for the garage, then go back:

• steel 200 l barrel;
• schweller;
• pipes.

Sequence of operations

• the top of the barrels remove;
• less edges;
• making the lid;
• we carry out a hole in it;
• we weld the channel;
• we weld the pipe with a diameter of 15 cm in the upper part - it is chimney;
• in the center of the lid we place a pipe with a diameter of 10 cm for air supply. She must perform above the barrel.

Operation of a wood-burning furnace

After the manufacture, the homemade oven for the garage you need to experience:

• fill the stove on 1/3 of its volume of firewood;
• install the pipe that will serve air and close the lid. When the firewood burns, the lid lowers;
• fuel through the pipe slightly wet the kerosene and throw the match.

If everything is done correctly, then the metal furnace for the garage will burn at least 7 hours. And if the entire volume is filled with firewood, then all 60.

Other types of garage heating furnaces

Brick

Brick ovens for the garage must be compact, and otherwise their design is similar to conventional furnaces:

• before proceeding with the masonry, the base is preparing: a polyethylene film, and on it sand 1 cm layer;
• then 11 rows of brickwork;
• the seams are expanded;
• the plate surface is refined.

Warm will be covered with firewood, and then quickly cools.

Gas

The gas furnace for the garage is effectively and very convenient, and even if there is a line along which gas is supplied. But deciding to pull the garage in this way, you will have to face gas services that will present how many requirements that it is hardly possible to fulfill them. Nevertheless, if you overcome all obstacles, you will not have any special concerns with the oven for heating the garage. This option can be called perfect.