In our climatic zone without heating in the winter it is simply not to do. There is no special choice between the heating tools in private houses. Most often used autonomous generators. It is worth noting that heating with such equipment costs somewhat cheaper than the classic homemade. Also, the personnel installation of the equipment will save a lot of money. The point is responsible, but small instructions and advice will help in a short time to launch the equipment and enjoy warmth in the house.

Features and generator design

In private homes, vortex heat generators are often used. In turn, they differ in shape. Ten years ago, tubular modifications were used, and round, oval and asymmetric heat generators are popularly popular. The device itself is small, but ensures optimal heating of a large private house. In some cases, the heat generator allows for a housing with warm water.

The vortex heat generator is a small device capable of converting a cold air flow into warm. The so-called "hot" end of the generator is capable of separating air at a temperature of about 200 ° C. Accordingly, the air flow from the "cold" end may have a temperature to -50 ° C. Many specialists note that, unlike other heating, this electric The device has no moving parts. This suggests that in a residential building, it is absolutely safe to use such an aggregate. Installation uses pipes made of stainless steel. Such material is best opposed to high temperatures, and heat efficiency is always at the height.

Air enters the generator chamber and accelerates already in the installation itself to the colossal speed. Inside the installation, the air is mounted on the electric shield. In some cases, this generator is used to cool the room. To do this, you will need to reconfigure the generator. Unlike other thermal installations used in production and in multi-storey buildings, the vortex heat generator has a slightly smaller efficiency. However, for a small private house, nothing better was invented.

The main advantages of the vortex heat generator

1. A large temperature difference between the cold and hot air flow.
2. The efficiency of the generator is up to 92%.
3. The impossibility of overheating the system due to the specifics of the structure.
4. The minimum loss of thermal energy during the operation of the device.
5. Optimal heating from 100 square meters of dwellings.

The main disadvantage of such an installation is still a high cost. At the same time, the analogues of the vortex heat generator are expensive to buyers even more expensive. Fortunately, during the operation of the installation, it will not be necessary to spend money on its setting and repair. Since the design and the principle of work itself is simple as possible, it is possible to understand everything yourself.

Creating a heat generator with your own hands

Obviously, from scratch to make a heat generator almost impossible. For the production of such equipment, a serious technological process is involved in modern enterprises. You can collect a small design with your own hands, which best repeats all the features of the vortex heat generator. It is called the heat generator of Potapov. Its efficiency is 93%.

The mixing nozzle is attached to the pressure pump with a flange. The pump serves a fluid with a pressure of 5-6 atmospheres. If water gets into the collector, a kind of whirlwind is created. The water vortex moves along the spiral tube to the "hot" end. At the end of the nozzle there is a donyshko, in the center of which there is a small hole from the withdrawal of hot water. To monitor the flux of hot water, a special braking device is provided, which is located right in front of the bottom. During the movement of water to the rectifier, the axial section creates a counter-flow course. To monitor the flow of cold water, you will need another disc flush rectifier. In the event that it is warm from the liquid, it must be sent by bypass, straight to the "hot" end. There, water is mixed with warm liquid using a mixer.

The engine is necessary for the health of the heat generator. In our case, the equipment is suitable for connecting to the network 220 V. The thermal generator itself needs to be fixed on the bed (fixed base). We also need the following equipment:

• sander;
• drill and drill set;
• welding machine;
• fasteners (bolts, nuts, etc.);
• primer and brush.

With the help of a grinding circle, it is necessary to cut apartments. Rectangular design (see drawing) is going very simple. Such equipment can be collected using bolts and nuts, or by using welding. Of course, in the first case you will have to do the holes of the drill. It should be closely followed by all sizes so that the design corresponds to all the necessary parameters.

Another square will need to attach to the design in the form of cross. This will consolidate the engine on the bed. The painting of the frame is performed. In the created frame, you must drill holes for installing the design.

Next, the pump is set. You should also calculate the power so that the engine can easily run the pumping unit without any problems.

Connecting the pump to the system begins with its connection to the hole, from which water is fed under a certain pressure. The second nozzle is joined directly to the heating system. To adjust the temperature mode, the connector will be required to install a locking device. If you cover it up, the temperature in the system will start climbing.

Often, various electronic temperature control systems are also installed, but their cost is quite high.